noise amplifier

P1 dB and IP3 are key parameters for the design of low noise amplifier. So correct analysis and optimization of them is very indispensable.

对低噪声功率放大器的设计，1dB压缩点（P1dB）和3阶截取点（IP3）是其2个关键参数，对他们进行正确的分析和优化是非常必要的。

The design of C band GaAs MMIC low noise amplifier was described.

主要介绍了C波段低噪声单片放大器的设计方法和电路设计指标.

The Design of Dual-band Low Noise Amplifier in Hybrid Integrated Circuits

混合集成双频段低噪声放大器的设计

An Overview of the Developing Situation and Structure Design of Low Temperature Low Noise Amplifier

低温低噪声放大器的发展概况及其结构设计综述

Purpose: High frequency low noise amplifier application, HF band amplifier application.

用途: 用于高频低噪声放大, 高频放大.

The microwave circuit unit is composed of microwave signal resource, low noise amplifier and microwave detector.

测量系统采用了微波信号源、低噪声放大器和微波检波器等组成微波电路单元。

Through this paper, it can be concluded that research from the design, manufacturing, and reliability test, a set of complete space low noise amplifier development plan, for its space application provides the basis.

通过本文研究，可以得出从设计、制造到可靠性验证等一套完整的低噪声放大器开发方案，为其宇航应用提供依据。

The application of low temperature low noise amplifier and some problems of structure design were introduced in this paper The work normal can be ensured.

本文介绍了低温低噪声放大器的应用情况，以及确保它正常工作所需的结构设计方面的一些问题。

Design of Low Noise Amplifier for Wireless Sensor Network

应用于无线传感器网络低噪声放大器的设计

Signal adjusting could filter the noise, interference outside of L1-band and amplify its power through band pass filter ( BPF) and low noise amplifier ( LNA).

其中，信号调整主要是利用前级带通滤波器和低噪声放大器将L1波段以外的噪声和干扰滤除，同时对其功率进行放大。

Purpose: High frequency low noise amplifier, VHF band amplifier application.

用途: 用于高频低噪声放大, 甚高频放大.

Design, simulation and realization of power amplifier and low noise amplifier are discussed in this article, including RF amplifiers circuit and DC feed circuit.

基于工程开发的需要，本文讨论了功率放大器和低噪声放大器的设计、仿真及整个电路的实现方法，包括射频放大电路和直流馈电电路，并提供了相关的仿真结果和测试结果。

Design of a Low Voltage Neutralized CMOS Differential Low Noise Amplifier

低压中和化CMOS差分低噪声放大器设计

But for the short of time we just test the Lange coupler and the low noise amplifier, more work such bugging and test need to be down in the future.

由于时间的关系，目前仅进行了兰格耦合器和单级放大器模块的测试，进一步的调试和改进将在以后进行。

Purpose: low noise amplifier at VHF, UHF and CATV band applications.

用途: 用于甚高频 、 超高频和有线电视频段的低噪声放大.

Then it presents the difficulties about the design of low noise amplifier after reading a large number of literatures, including the matching network, the stability of the transistor and so on.

在阅读大量相关文献的基础上，分析了低噪声放大器研制过程中遇到的困难，包括匹配电路的设计以及提高晶体管稳定性的方法等等问题。

Structure design of low temperature low noise amplifier

低温低噪声放大器测试平台的结构设计